分子印迹膜的制备研究进展

将分子印迹技术与膜分离技术相结合的分子印迹膜,由于其高选择性,近年来受到了国内外研究者的广泛关注.本文初步探讨了分子印迹膜(MIM) 的两种分离机理以及目前主要的制备方法:同步法和复合法.     

Dislocation Analysis for Large-sized Sapphire Single Crystal Grown by SAPMAC Method

In this paper,large-sized sapphire (230×210 mm,27.5 kg) was grown by SAPMAC method (sapphire growth technique with micro-pulling and shoulder-expanding at the cooled center). Dislocation peculiarity in large sapphire boule (0001) basal plane was investigated by chemical etching,scanning electron microscopy and X-ray topography method. The triangular dislocation etch pit measured is 7.6×101～8.0×102 cm-2,in which relative high-density dislocations were generated at both initial and final stages of crystal growth. The analysis of single-crystal X-ray topography shows that there are no apparent sub-grain boundaries; the dislocation lines are isolated and straight. Finally,the origins of low-density dislocation in sapphire crystal are discussed by numerical analysis method.     

Evaluation of measurement uncertainty for analytical procedures using a linear calibration function

In the EURACHEM/CITAC draft ”Quantifying uncertainty in analytical measurement” estimations of measurement uncertainty in analytical results for linear calibration are given. In this work these estimations are compared, i.e. the uncertainty deduced from repeated observations of the sample vs. the uncertainty deduced from the standard residual deviation of the regression. As a result of this study it is shown that an uncertainty estimation based on repeated observations can give more realistic values if the condition of variance homogeneity is not correctly fulfilled in the calibration range. The complete calculation of measurement uncertainty including assessment of trueness is represented by an example concerning the determination of zinc in sediment samples using ICP-atomic emission spectrometry. Received: 9 February 2002 Accepted: 17 April 2002     

An investigation of the reliability of the Galerkin-Petrov method

It is shown that the Galerkin-Petrov method if applied in a controlled way yields reliable results for excited states of the same symmetry classifications as the ground state. Computations are performed for the 2¹ S and 3¹ S states of He. The problem of optimizing nonlinear parameters of the basis functions by means of the GP method is discussed. A special optimization scheme is suggested and numerically illustrated for someS states of He.     

Validation steps for traceability of linear calibrated chemical measurements

Based on the new draft of the EURACHEM/CITAC Guide Traceability in Chemical Measurement, this publication describes how traceability can be achieved for chemical measurements using a linear calibration function. Traceability can be accomplished without larger expenditure, if the measurement is calibrated on the basis of appropriate reference standards and the linear regression employed is selected and validated statistically in a suitable form. The determination of nickel in aqua regia eluates of sediment samples, employed for an ICP-OES measurement, is used as a practical illustration of this approach.     

HPLC of antibiotics. 1. Streptolydigin and related compounds

Two new acyltetramic acids related to streptolydigin have been isolated from fermentations of Streptomyces lydicus. The principal members of this complex were resolved by TLC on silica gel. However, the methods of detection, permanganate spray or bioautography, were not suitable for both crude fermentation broths and purified extracts. Gas chromatography is unsuitable for the detection of either underivatized or silylated streptolydigins. High performance liquid chromatography (HPLC) particularly on triethylaminoethyl cellulose is rapid and sensitive and is the method of choice for the analysis of both crude and purified samples. Using high performance liquid chromatography, two components were detected in the complex, which are not observed using any of the other chromatographic procedures.     

Determination of acidic chlorinated pesticides in water: Comparison of official EPA method 515.1 and liquid-solid extraction HPLC/UV and HPLC/PBMS analyses

Summary A comparison of the official EPA method 515.1 for determination of chlorinated acidic pesticides and a modification of it is illustrated. Extraction of the analytes from water and their determination and quantitation is by gas chromatography-electron capture detection (GC-ECD), liquid chromatography-UV detection and liquid chromatography-particle beam mass spectrometry. Although HPLC-PBMS was found to be less sensitive than the GC-ECD method, it was, nevertheless, more sensitive than HPLC-UV. The modified method is simpler, quicker and allows more accurate determination of pesticides in aqueous samples.Deceased July 31, 1996     

Valence Bond Study of Dissociation Behavior and Spectroscopic Constants for the Ground States of LiF and NaF

ＩｎｔｒｏｄｕｃｔｉｏｎＴｈｅａｌｋａｌｉｈａｌｉｄｅｄｉａｔｏｍｉｃｍｏｌｅｃｕｌｅｓｐｒｏｖｉｄｅａｔｙｐｉｃａｌｃｕｒｖｅｃｒｏｓｉｎｇｐｒｏｂｌｅｍ［１］．Ｔｈｅｏｕｔｓｔａｎｄｉｎｇｎｏｎａｄｉａｂａｔｉｃｂｅｈａｖｉｏｒｏｆｔｈｅｃｈｅｍ...     

A method for correcting the contact angle from the θ/2 method

The θ/2 method, a widely used technique on measuring the contact angle of a sessile drop, assumes that the drop profile is part of a sphere. However, the shape profile of a sessile drop is governed by the Young–Laplace equation and is different from a sphere, especially for drops with a large bound number (e.g. large volume or small surface tension). The spherical assumption, therefore, causes errors on evaluating the contact angles. The deviation of contact angle from the θ/2 method is evaluated from a theoretical calculation in this work. A simple means is given for correcting the measurement error. The corrected angle results from the drop volume, surface tension, liquid density and the contact angle from θ/2 method. An algorithm for finding the correct contact angle without knowing the density and surface tension is also given. At the end, two examples of pendant drops are given for the illustration.     

STRUCTURE EVOLUTION OF POLYMER CHAINS FOR NECKING FORMATION IN HIGH-SPEED FIBER SPINNING PROCESS

Finite element method is used to simulate the high-speed melt spinning process,based on the equation system proposed by Doufas et al.Calculation predicts a neck-like deformation,as well as the related profiles of velocity,diameter, temperature,chain orientation,and crystallinity in the fiber spinning process.Considering combined effects on the process such as flow-induced crystallization,viscoelasticity,filament cooling,air drag,inertia,surface tension and gravity,the simulated material flow behaviors are consistent with those observed for semi-crystalline polymers under various spinning conditions.The structure change of polymer coils in the necking region described by the evolution of conformation tensor is also investigated.Based on the relaxation mechanism of macromolecules in flow field different types of morphology change of polymer chains before and in the neck are proposed,giving a complete prospect of structure evolution and crystallization of semi-crystalline polymer in the high speed fiber spinning process.